Clarion CDC655TZ CDC655Tz User Manual

English  
280-7326-00  
3. Remove the floor carpet and decide on the place  
to install. Adjust the installation bracket with bolts  
to suit the place of installation.  
Extracting the Magazine  
1. Open the flip down door.  
Installation Procedure  
1. Use the double seamed hexagonal bolts to fix the  
lead clamp and installation bracket to the unit (on  
both sides) in the desired direction of installation.  
Caution  
6 DISC CD CHANGER WITH  
CD TEXT Owner’s manual  
IDENTIFICATION OF PARTS  
4
Dust and other objects may cause malfunc-  
tions if they get into the unit.  
2. Press the eject button and take out the magazine.  
The installation bracket with bolt may be broken  
off if it is bent many times at the perforated line.  
1 Installation selector levers  
Always be sure to shut the flip down door once  
finished with loading or unloading the maga-  
zine.  
<Vertical Position>  
<Horizontal Position and  
Suspending Position>  
2 Eject button  
Thank you for purchasing the CDC655Tz/RDC655Tz sys-  
tem.The CDC655Tz/RDC655Tz is designed incorporat-  
ing the latest digital technologies, while featuring a newly  
developed CD mechanism to achieve excellent perform-  
ance and good reliability.  
Press the eject button for ejecting the magazine.  
3 Flip down door  
4 CeNET terminal for input and output  
(13-pin)  
Eject button  
Please read this owners manual entirely before proceed-  
ing with installation.  
5 Digital optical fiber output terminal  
2. Use the wing nut to hold in place the installation  
bracket with bolt to the installation bracket, which  
is attached to the unit.Then affix the cushion rub-  
ber.  
4. Remove the separator of the cushion rubber that  
is attached to the installation bracket with bolt and  
install accordingly.  
6 Address switch  
When connecting an CD changer and MD changer  
by CeNET, no more than 2 units can be connected.  
When both of them are CD, the address switch needs  
to be reset so that the address switch number is not  
the same for each.  
MODEL  
CDC655z  
CLASS 1  
LASER PRODUCT  
12V  
GROUND  
5. Unfasten the wing nut and remove the unit.  
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES.  
OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDI-  
TIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFER-  
ENCE, AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE  
RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE  
UNDESIRED OPERATION.  
<Vertical Position>  
<Suspending Position>  
Clarion Co.,Ltd.  
MADE IN J
SYSTEM EXAMPLE  
051 722 877  
6
CAUTION  
6. Return the floor carpet to its original place. Use a  
knife to cut into the carpet where the bolt can be  
felt, and allow the bolt to protrude from the carpet.  
1.Be sure to use the screws,etc., included in the package for installa-  
tion. Using other screws could damage the set.  
ISO  
THIS PRODUCTION COMPLIES WITH DHHS RULES 21 CFR SUB-  
CHAPTER  
J
APPLICABLE AT DATE OF MANUFACTURE.  
8
2.Set the selectors on both side panels to the HPosition when  
installing the set horizontally, to the Vposition when installing the  
set vertically. When installing at the angle of 45˚, set the selectors to  
the center click position.  
CLARION CO.,LTD.  
50 KAMITODA, TODA-SHI, SAITAMA-KEN, JAPAN.  
Screws  
This unit is available for upgrade in various ways.  
M5×8 W-SEMS  
<How to change the address switch>  
M
A
N
U
FA  
C
TU  
R
E
D
:
H
The set may be damaged if the selectors are not set to the proper  
positions.  
45  
°
V
When you want to upgrade the system, make sure that the upgrade unit fits and wire it correctly.  
2
3
SERIAL No.  
1
1. Rotate and change the switch using a fine-tipped  
screwdriver.  
4
Source unit  
2. Rotate the switch until it clicks into position.  
Address switch  
This equipment has been tested and found to com-  
ply with the limits for a Class B digital device, pursu-  
ant to Part 15 of the FCC Rules.  
USE OF CONTROLS, ADJUSTMENTS, OR PER-  
FORMANCE OF PROCEDURES OTHER THAN  
THOSE SPECIFIED HEREIN, MAY RESULT IN  
HAZARDOUS RADIATION EXPOSURE.  
THE COMPACT DISC PLAYER SHOULD NOT BE  
ADJUSTED OR REPAIRED BY ANYONE EXCEPT  
PROPERLY QUALIFIED SERVICE PERSONNEL.  
<Example of address switch setting>  
CeNET cable  
G Setting example 1  
7. Align the unit with the bolts and secure it with the  
wing nuts.  
CD changer  
<Horizontal Position>  
These limits are designed to provide reasonable pro-  
tection against harmful interference in a residential  
installation.This equipment generates, uses, and can  
radiate radio frequency energy and, if not installed  
and used in accordance with the instructions, may  
cause harmful interference to radio communications.  
However, there is no guarantee that interference will  
not occur in a particular installation.If this equipment  
does cause harmful interference to radio or televi-  
sion reception, which can be determined by turning  
the equipment off and on, the user is encouraged to  
consult the dealer or an experienced radio/TV tech-  
nician for help.  
1
Address switch  
number 1  
Important  
Source unit  
RCA extension cable  
Be sure that the CD changer  
numbers are not the same.  
2
CHANGES OR MODIFICATIONS NOT EX-  
PRESSLY APPROVED BYTHE MANUFACTURER  
FOR COMPLIANCE COULD VOID THE USERS  
AUTHORITY TO OPERATE THE EQUIPMENT.  
INFORMATION FOR USERS:.  
CD changer  
Ferrite clamp  
MD changer  
Address switch  
number 2  
CeNET wire bound  
DPH7500z  
(Gray)  
G Setting example 2  
CD changer  
CHANGES OR MODIFICATIONS TO THIS PROD-  
UCT NOT APPROVED BYTHE MANUFACTURER  
WILL VOIDTHE WARRANTY AND WILLVIOLATE  
FCC APPROVAL.  
1
Address switch  
number 1  
Important  
(Black)  
(Black)  
Source unit  
Do not use address switch  
numbers 3or 4.  
(Gray)  
MD changer  
Address switch  
number 1  
TROUBLESHOOTING  
CeNET wire bound  
9
1
FEATURES  
1
Y-adapter  
Digital optical fiber cable  
Symptom  
Cause  
Remedy  
G 6-Disc Capability  
G Spring-Loaded Silicon Oil-Dampened Suspension  
Caution  
Loss of power  
Bad connection.  
Check connections. Connect the cable again.  
System  
G CeNET with Balanced Audio Line Transmission  
Connection with  
the source unit is The length of the CeNET Rewire the connection so that the length of cable is less than 65.62 ft  
not recognized.  
and Dynamic Noise Canceling  
G Eject Capability While lgnition-Off  
G 120˚ Mounting Capability  
G Optical Digital Output  
• The unit may not operate when both CD  
changers are set to the same address switch  
number.  
• Do not use address switch numbers “3or “4”.  
cable wiring is more than (20m).  
65.62 ft (20m).  
INSTALLATION OF CONNECTORS  
G 8-Times Oversampling Digital Filter  
G Dual 1-Bit D/A Converters  
G Zero-Bit DetectorMute Circuit  
G 3-Beam Laser System  
Not used.  
7
CeNET cable  
Address switch num- When the 2 CD changers are connected, set the address switch so  
• Never change the address switch during op-  
eration. Doing so can cause malfunction or  
breakdown. Do not change the address switch  
forcibly, because this may also cause  
malfunciton.  
2 3  
Note:  
G CD TEXT  
bers are the same.  
that they do not have the same address number. Refer to the Exam-  
ple of address switch settingin the section titled IDENTIFICATION  
OF PARTS.  
1
4
Only the provided screws and brackets should be used during installation. Us-  
ing screws other than those specified will cause damage.  
G Dimensions:  
8.9"(225mm)W × 2.5"(63mm)H × 6.6"(167mm)D  
Address switch  
When the CeNET cable is connected, it must be inserted fully and  
securely. After connecting, fasten the cable using the cable holder or  
cable clamp. After connecting, fasten the cables with cable holders,  
etc.  
Magazine cannot Magazine inserted Insert correctly.  
be loaded.  
wrongly.  
• The CeNET cable wiring must be less than 65.62  
ft (20m) in length.  
PRECAUTIONS  
2
A magazine is already Eject the magazine and insert the other.  
in the player.  
Digital optical  
fiber cable  
When removing the digital optical fiber cable, rotate it to loosen it and  
pull it gently while holding the slide cap (a gray color part on the source  
unit).  
1. This unit does not operate independently.The unit must be used with a source unit that has a cable connec-  
tion for CeNET wire bound (sold separately).  
Slide cap  
Distorted magazine.  
Buy New Magazine CAA-355.  
2. CD singles cannot be used.  
No Discsign  
appears when  
searching for  
discs.  
Disc inserted upside- Read the section on Inserting The CDcarefully and reinsert the CD  
CD MAGAZINE  
5
down. correctly.  
Do not coil up the digital optical fiber cable with a radius of less than 1"  
(3 cm).With a radius of less than 1", the performance of the cable will  
be greatly impaired.  
3. G The pickup, the heart of a player, is built in deep behind the door. Do not leave this door open for extended  
periods to prevent dust adhering to the pickup.  
Moisture or dirt on disc. Wipe disc free of moisture and dirt.  
Inserting the CD  
1. Turn the magazine over onto its back, put your  
finger on the disc holder release knob and draw  
out the disc holder.  
G When the inside of the car is very cold and the player is used soon after switching on the heater, dew may  
form on the disc or optical parts of the player and proper playback may not be possible. If dew forms on the  
disc, wipe it with a soft cloth. If dew forms on the optical parts of the player do not use the player for about  
one hour and the condensation will disappear naturally to allow normal operation.  
Noise, skipping  
The installation selec- Set the installation selector levers to the same position on both sides.  
When installed in a glove box or console box, make sure that the source  
unit cables or cords do not interfere with the opening or closing of the  
flip down door.  
3. Press in on the disc holder until it locks securely  
into the magazine. After loading a CD, make sure  
that it is correctly loaded.  
tor levers are set to dif-  
ferent positions on both  
sides.  
Magazine  
4. While the system is in play, do not plug or unplug the cables as this will cause damage.  
The unit installation di- Set the unit installation direction and the installation selector lever  
rection and the instal- positions to match each other.When installed at an angle, change the  
lation selector lever po- installation selector lever to a position (H, 45˚, V) not prone to noise or  
Disc holder  
Caution  
5. This unit is compatible with CD TEXT. When it is connected to a center unit suitable for CDTEXT display, CD  
TEXT can be displayed. (When it is connected to a center unit without CDTEXT function, CD TEXT can not  
be displayed.)  
sitions do not match.  
sound loss.  
Look through the magazine opening and  
check whether or not the CD is tilted. If the  
CD is not in the slots on either side of the disc  
holder, either the mechanism or CD may be  
damaged.  
If the disc holder does not slide in fully, or  
slides with difficulty,it is possible that the CD  
is not correctly loaded.Reload in such cases.  
INSTALLATION  
Disc holder  
8
6. Do not expose the magazine to direct sunlight, the car heater or other sources of strong heat. Replace the  
CD magazine (CAA-355) with a new one if bent or otherwise damaged.  
Disc bent or badly Compare with another disc. If bad, discard the damaged disc.  
damaged.  
Prior to Installation  
Disc is very dirty.  
Clean the disc.  
1. Before attempting to use this unit you must first  
remove the packing safety lockscrews (3 positions)  
with a screwdriver. Store these lockscrews care-  
fully so they can be used again if needed.  
2. Decide on the installation place and direction.  
Caution  
The signal side of the CD  
Release knob  
3. Insert an item such as a screwdriver with a fine  
point or the tip of a ballpoint pen into the round  
hole of the installation selector lever to switch to  
the position you need.  
Mechanism does Mechanical error.  
not function.  
1. Referring to section INSTALLATION, check the three angle of in-  
stallation selector levers are properly set. If not, set them at the  
proper position for the angle of installation.  
ONLY use the magazine included with the CDC655Tz, RDC655Tz, CDC655z or RDC655z. For addi-  
tional magazines, purchase Clarion Model CAA335. Do not attempt to insert different style magazine  
into the CD changer even if they fit into the magazine opening. Inserting other manufacturersmaga-  
zines or previous Clarion 6 Pack style magazines into the CDC655Tz, RDC655Tz, CDC655z or RDC655z  
will cause damage to the mechanism and void the warranty.  
2. Line up the CD with the groove of the disc holder.  
Make sure the label on the CD faces downwards.  
2. Check whether The CD magazine can be ejected by pressing the  
CD magazine eject button, then insert a new CD magazine.  
Note:  
Do not place CDs in the disk holder from above.  
H
Magazine is  
ejected evenwhen  
inserted into the  
unit.  
Disc holder is not cor- Read the section on Inserting the CDcarefully and reinsert the disc  
rectly inserted into the holder correctly.  
magazine.  
45°  
Caution  
V
Note:  
Before shipment from the factory, the levers are nor-  
mally placed in the horizontal position.  
CAUTIONS ON HANDLING CDs  
Lever  
Pulling strongly on the disc holder may cause it  
to come out of the magazine. In such cases,  
press in on the disc holder tabs and re-insert  
into the magazine. Be sure that the disc holder  
is correctly inserted.  
3
Reinstall these lockscrews when shipping the unit  
back for repair.  
lf the same phenomenon still occurs after checking the above, or it is impossible to remove the magazine, please  
consult your local dealer.  
Use only compact discs bearing the  
mark and the  
mark.  
Magazine  
Do not play heart-shaped, octagonal, or other specially shaped compact discs.  
H: Horizontal  
45˚: Slope  
V:Vertical  
Handling  
G Do not use commercially available CD protection  
Disc Holder  
G New discs may have some roughness around the  
edge.The set may not work or the sound may skip  
if such discs are used. Use a ball-point pen, etc.,  
to remove roughness from the edge of the disc.  
sheets or discs equipped with stabilizers, etc.  
These may get caught in the internal mechanism  
and damage the disc.  
H
H
H
°
45°  
45°  
45°  
SPECIFICATIONS  
30  
10  
2. Insert the magazine (facing up as shown below)  
into the unit with the CD load/unload side on the  
right.Press the magazine into the unit until it locks  
securely.  
V
Storage  
Extracting the CD  
Take out the CD after pulling out the disc holder.  
V
V
Frequency Response  
Signal-to-Noise Ratio  
Wow and Flutter  
Power Supply  
: 5Hz~20kHz( 1dB)  
: 105dB(1kHz)IHFA  
: Below measurement limits  
: DC14.4V (10.8~15.6V) negative ground  
: Less than 1A  
G Do not expose compact discs to direct sunlight or  
Ball-point pen  
Roughness  
Align the installation selector le- Align the installation selector le-  
vers on both sides of the unit with vers on both sides of the unit with  
the “H” position.  
Align the installation selector le-  
vers on both sides of the unit with  
the Vposition.  
any heat source.  
G Do not expose compact discs to excess humidity  
the 45°position.  
or dust.  
Current Consumption  
G Do not expose compact discs to direct heat from  
Unit Weight  
Dimensions  
: 3.74lb. (1.7kg)  
: 8-7/8"(Width) × 2-1/2" (Height) × 6-9/16"(Depth)  
[225mm(W) × 63mm(H) × 167mm(D)]  
1.  
heaters.  
Caution  
Cleaning  
G Never stick labels on the surface of the compact  
G To remove fingermarks and dust, use a soft cloth  
and wipe in a straight line from the center of the  
compact disc to the circumference.  
disc or mark the surface with a pencil or pen.  
Set the installation selector lever to the same position on both sides.  
Due to improvements, the design and these specifications may be modified without prior notice.  
Note:  
2.  
G Never play a compact disc with any cellophane  
tape or other glue on it or with peeling off marks.  
If you try to play such a compact disc, you may  
not be able to get it back out of the CD player or it  
may damage the CD player.  
When the unit is installed below the horizontal position (up to 15 degrees) the ejected magazine,  
when left in that position, will drop due to vibrations from the car.  
When taking out the CD do not let your fingers touch  
the signal side of the CD.  
G Do not use any solvents, such as commercially  
available cleaners, anti-static spray or thinner to  
clean compact discs.  
3. Close the flip down door.  
Adjust the installation selector levers into the correct locations. Setting the locations incorrectly or  
in varied positions will cause skipping.  
Note:  
Inserting the Magazine  
1. Open the flip down door.  
Clarion Co.,Ltd.  
Do not move the installation selector levers while the unit is in use. This will cause damage to the  
mechanism and the disc.  
Never insert the magazine for 12-disc CD changer  
(CAA-122) into this unit because it can become stuck  
and impossible to remove.  
G After using special compact disc cleaner, let the  
All right Reserved. Copyright © 1998:Clarion Co., Ltd.  
G Always handle the compact disc by the edges.  
compact disc dry off well before playing it.  
Never touch the surface.  
Printed in Japan 1999/3 (To.K)  
PE-2300B / PE-2304B 280-7326-00  

Motorola i877 User Manual
Kyocera X tc M2000 User Manual
KitchenAid PROLINE SERIES KPES100 User Manual
Kenwood Z828MP User Manual
Jura Capresso Xf70 User Manual
Gemini CDX 1200 User Manual
Clarion BD216 User Manual
Blackberry 7100I User Manual
Arkon 400 User Manual
Addonics Technologies AESNAPMRSA User Manual